Lighting Load Controller Settings

Horizon Dimmers and Switches

Tap the gear button next to the device name to display a Settings dialog box for the dimmer or switch. The About tab is selected and displays the device information.

Status

Tap the Status tab to view the status of the dimmer or switch.

Min/Max

Tap the Min/Max tab to set the minimum and maximum dimmer level.

Set the Dimmer Min Level and Dimmer Max Level:

  • Dimmer Min Level: The lowest level that the lights will dim to. This may help prevent flickering at low levels.
  • Dimmer Max Level: The highest level that the lights will raise to. This will prevent the lights from being too bright in the room when at full brightness.

Curve Type

Tap the Curve Type tab to configure the curve type that is used to dim the load. Select Linear or Logarithmic based on the load type.

Set the Curve Type:

  • Linear: Dim the load using a linear dimming curve.
  • Logarithmic: Dim the load using a logarithmic dimming curve.
  • Custom: Dim the load using a custom dimming curve. Create the dimming curve using Crestron Toolbox™ software.

Load Type

Tap the Load Type tab to match the type of load that is connected to the dimmer.

Set the Load Type:

  • Local Settings: Dims the load using the dimming mode set locally on the dimmer.
  • Auto: Dims the load using forward or reverse phase dimming. The dimmer selects the best dimming mode based on the type of load that is attached.
  • Reverse: Dims the load using reverse phase dimming (trailing-edge dimming). Typically used with incandescent, dimmable LED, or electronic low-voltage (ELV) loads.
  • Forward: Dims the load using forward phase dimming (leading-edge). Typically used with magnetic low-voltage (MLV) loads.
  • Non Dim: The load type is not dimmable. The dimmer functions a switch and switches the load between full on (100%) and full off (0%). Ramp and fade times are ignored. Overrides the functionality set on the dimmer.

Update

Use the Update tab to update the device firmware.

  • Current Version: Displays the current firmware version for the gateway.
  • Available Version: Displays the available firmware version for the gateway.
  • Update: If a firmware update is available, tap Update to update the firmware.
  • Check For Update: Tap the Check For Update button to search for firmware updates for the gateway.

Replace Device

Tap the Replace Device tab to replace the dimmer.

Voice Control

Tap the Voice Control tab to change the voice control settings.

NOTE: To use voice control, voice control services must be turned on and configured. For details, refer to Voice Control Settings.

  • Enable Status: Select Enable or Disable to turn voice control services on or off.
  • Description: Enter a descriptive name. The name is used by the voice control services.

DIN‑DALI‑2 Groups (Loads)

Tap the gear button next to the device name to display a Settings dialog box for the DIN-DALI-2 group (load). The About tab is selected and displays the device information. The Settings dialog box has additional tabs for Min/Max, Curve Type, and Voice Control.

Min/Max

The Dimmer Min Level and Dimmer Max Levels are set using the DALI Commissioning tool in the Crestron Toolbox™ application. The settings cannot be changed and will revert to 0 and 100. For additional details, refer to Add a DALI Gateway.

Curve Type

Tap the Curve Type tab to configure the curve type that is used to dim the load. Select Linear or Logarithmic based on the load type.

Voice Control

Tap the Voice Control tab to change the voice control settings.

NOTE: To use voice control, voice control services must be turned on and configured. For details, refer to Voice Control Settings.

  • Enable Status: Select Enable or Disable to turn voice control services on or off.
  • Description: Enter a descriptive name. The name is used by the voice control services.

DMX-C Fixture Groups (Loads)

Tap the gear button next to the device name to display a Settings dialog box for the DMX-C fixture group (load). The About tab is selected and displays the device information.

Voice Control

Tap the Voice Control tab to change the voice control settings.

NOTE: To use voice control, voice control services must be turned on and configured. For details, refer to Voice Control Settings.

  • Enable Status: Select Enable or Disable to turn voice control services on or off.
  • Description: Enter a descriptive name. The name is used by the voice control services.

DMX-C Fixture (Loads)

Tap the gear button next to the device name to display a Settings dialog box for the DMX-C fixture (load). The About tab is selected and displays the device information.

Details

Tap the Details tab to view information about the fixture.

Replace Device

Tap the Replace Device tab to replace the device.

PhaseX Fixture (Loads)

Tap the gear button next to the device name to display a Settings dialog box for the PhaseX fixture (load). The About tab is selected and displays the device information.

Details

Tap the Details tab to view information about the fixture.

Replace Device

Tap the Replace Device tab to replace the device.