Shade Motor and Motor Controller Settings

CSM-QMTDC Series Motors

Tap the gear button next to the device name to display a Settings dialog box for the shade motor. The About tab is selected and displays the device information. The Settings dialog box has additional tabs for Limits, Update, Speed, Replace Device, and Voice Control.

Limits

Tap the Limits tab to configure the shade motor limits. The lower limit is the lowest point that the shade fabric will travel and the upper limit is the highest point that the shade fabric will travel.

To set the lower limit:

  1. Tap the Adjust Lower Limit button.
  2. Tap and hold the Raise and Lower buttons or tap the Jog Up or Jog Down buttons to set the fabric height at its lower limit.
  3. Tap the Save Limit button.

To set the upper limit:

  1. Tap the Adjust Upper Limit button.
  2. Tap and hold the Raise and Lower buttons or tap the Jog Up or Jog Down buttons to set the fabric height at its upper limit.
  3. Tap the Save Limit button.

Update

Tap the Update tab to update the firmware for the shade motor. Tap Check for Update to search for updated firmware. If a firmware update is available, tap Update to update the firmware for the shade motor.

Speed

Tap the Speed tab to set the speed, in revolutions per minute (RPM), that the shade travels. The value can be set between 15 and 30 revolutions per minute.

  • Default: Sets the revolutions per minute to the default value. The default value is 25 revolutions per minute.
  • Close: Fully closes the shade.
  • Open: Fully opens shade.

Replace Device

Tap the Replace Device tab to replace the device.

Voice Control

Tap the Voice Control tab to configure the voice control settings.

NOTE: To use voice control, voice control services must be turned on and configured. For details, refer to Voice Control Settings.

  • Enable Status: Select Enable or Disable to turn voice control services on or off.
  • Description: Enter a descriptive name. The name is used by the voice control services.

CSM-QMTDC Battery Shades

Tap the gear buttonnext to the device name to display a Settings dialog box for the shade motor. TheAbout tab is selected and displays the device information. The Settings dialog box has additional tabs forLimits,Speed,Update,Replace Device, andVoice Control.

Limits

Tap theLimits tab to configure the shade motor limits. The lower limit is the lowest point that the shade fabric will travel and the upper limit is the highest point that the shade fabric will travel.

To set the lower limit:

  1. Tap theAdjust Lower Limit button.
  2. Tap and hold theRaise andLower buttons or tap theJog Up or Jog Down buttons to set the fabric height at its lower limit.
  3. Tap theSave Limit button.

To set the upper limit:

  1. Tap theAdjust Upper Limit button.
  2. Tap and hold theRaise andLower buttons or tap theJog Up or Jog Down buttons to set the fabric height at its upper limit.
  3. Tap theSave Limit button.

Update

Tap theUpdate tab to update the firmware for the shade motor. TapCheck for Update to search for updated firmware. If a firmware update is available, tapUpdate to update the firmware for the shade motor.

Speed

Tap theSpeed tab to set the speed, in revolutions per minute (RPM), that the shade travels. The value can be set between 10 and 18 revolutions per minute.

  • Default: Sets the revolutions per minute to the default value. The default value is 18 revolutions per minute.
  • Close: Fully closes the shade.
  • Open: Fully opens shade.

Replace Device

Tap the Replace Device tab to replace the device.

Voice Control

Tap the Voice Control tab to configure the voice control settings.

NOTE: To use voice control, voice control services must be turned on and configured. For details, refer to Voice Control Settings.

  • Enable Status: Select Enable or Disable to turn voice control services on or off.
  • Description: Enter a descriptive name. The name is used by the voice control services.

CLC-MCEX

Tap the gear button next to the device name to display a Settings dialog box for the motor controller. The About tab is selected and displays the device information. The Settings dialog box has additional tabs for Advanced, Replace Device, and Voice Control.

Advanced

Tap the Advanced tab to configure the motor controller.

  • Max Time: Sets the maximum time that the motor can move in the open or close direction. The value can be set between 1 and 600 seconds.
  • Lockout Time: Sets the minimum amount of time that the motor must remain in the stop state before changing direction. The value can be set between 0.02 to 2 seconds.
  • Jog Time: Sets the time that the motor will move during a jog open or jog close operation. The value can be set between 0.05 and 2 seconds.
  • Slave Switch Type: Sets the type of slave switch that is connected to the motor controller. The slave switch can be set to either Momentary or Sustained.

Replace Device

Tap the Replace Device tab to replace the device.

Voice Control

Tap the Voice Control tab to configure the voice control settings.

NOTE: To use voice control, voice control services must be turned on and configured. For details, refer to Voice Control Settings.

  • Enable Status: Select Enable or Disable to turn voice control services on or off.
  • Description: Enter a descriptive name. The name is used by the voice control services.