UCA-SMK-UC2 and UCA-SMKR-UC2-3

The Crestron UCA-SMK-UC2 and UCA-SMKR-UC2-3 are swivel mount accessories for Crestron Flex Tabletop Small Room Conference Systems. They enable tabletop conference device mounting with up to 170° rotation for optimal positioning. The UCA-SMK-UC2 is designed for mounting the UC-MM30 series tabletop conference device. The UCA-SMKR-UC2-3 is designed for the UC-MMX30 series tabletop conference device and has the following additional features:

• Retracts the installed USB-A to Micro USB-B cable, HDMI cable, and USB-C cable.

• Above the table, the USB-A, HDMI, and USB-C cables support Bring Your Own Device (BYOD) connectivity for the tabletop conference device.

• Below the table, the Micro USB-B, HDMI, and USB-C cables connect to the UC-PR which is included with the UC-MMX30.

UCA‑SMK‑UC2

UCA-SMKR-UC2-3

Installing UCA-SMK-UC2 and UCA-SMKR-UC2-3

The UCA-SMK-UC2 and UCA-SMKR-UC2-3 have similar installation instructions. For simplicity within this guide, the term "swivel mount accessory" is used except where otherwise noted.

In the Box

Qty.	Description
1	UCA-SMK-UC2 or UCA-SMKR-UC2-3 Swivel Mount Accessory (6511567 or 6511362)
	Additional Items
1	Locking ring with screws (4519116)
1	Cutout Template (4532125)
1	Allen wrench, 3/32 in. (2036829)

Install the Swivel Mount Accessory

Install the swivel mount accessory on any flat, level surface with a thickness of 1/2 in. (13 mm) minimum to 1-1/4 in. (32 mm) maximum. The LAN and USB cables for the UC-MM30 or UC-MMX30 tabletop conference device route through the cable cover of the swivel mount accessory, passing beneath the mounting surface for a completely hidden appearance. Refer to the Mount the Swivel Mount Accessory section for more information.

UCA‑SMK‑UC2

UCA‑SMKR‑UC2‑3

Mount the Swivel Mount Accessory

When determining the mounting location, consider where users will be seated and their proximity to the swivel mount accessory and the tabletop conferencing system. The mounting location must accommodate a 170° swivel range. Additionally, the UCA‑SMKR‑UC2‑3 requires a 27.42 in. (696 mm) clearance for the cable retractor body below the table.

A 4 in. hole saw, a jigsaw, a 3/32 in. Allen wrench (included), and the cutout template (included) are required to mount the swivel mount accessory.

1. Secure the cutout template to the mounting location. The notch on the template and the swivel mount accessory indicates the front of the swivel mount accessory.

   

2. Use a hole saw (not included) to drill a 4 in. hole in the table.

3. Use a jig saw (not included) to cut the front notch.

4. Insert the body of the swivel mount accessory into the mounting hole. Match the notch on the front of the swivel mount accessory with the notch in the table.

5. Beneath the table, twist the included locking ring onto the body of the swivel mount accessory.

   Notes: 

   • Make sure the surface of the locking ring labeled TOP faces the bottom of the table.

     

   • Leave a 1/8 in. (4 mm) gap between the locking ring and the bottom of the table.

     

6. Secure the locking ring to the bottom of the table. Use a 3/32 in. Allen wrench (included) to tighten the three set screws included with the locking ring.

   

Connect and Dock the Tabletop Conference Device

Make the USB and LAN connections to the tabletop conference device before docking it to the swivel mount accessory, as the device blocks access to the cable cover pass-through holes. Once docked, continue making connections to the tabletop conference device.

To make the USB and LAN connections to the tabletop conference device:

1. Route the USB and LAN cables along the outside of the swivel mount body through cable cover pass-through holes.

   

2. Connect the USB and LAN cables to the tabletop conference device.

3. Use the optional cable clamp to hold the USB and LAN cables in place.